Additional fitting instructions: Co-cast brake disc

Additional fitting instructions: Co-cast brake disc
 
Please refer to the instructions in the Product box for assembly, warranty and refunds.
 
Disco originale Brembo interfuso con campana in acciaio e fascia frenante in ghisa ad alto tenore di carbonio (HC).
1. Original Brembo co-cast disc with steel hub and high-carbon cast iron braking surface.
Icona di equivalenza OE tra i dischi freno co-cast e disco originale Mercedes
2. Interchangeable and equivalent to the Mercedes original disc.
Icona di omologazione ECE-R90
3. UN ECE-R90 approved. Download the certificate from our website and keep it in your vehicle for inspection checks.
 
Avvertenza di maneggiare con cautela il Prodotto
4. CAUTION! Handle with care.
Indicazioni su come non ruotare lo sterzo
5. CAUTION! Avoid turning the steering wheel by holding the disc/caliper, as shown in the figure.
Numeri che indicano la corretta sequenza di avvitamento delle viti e per la coppia di serraggio per montare la ruota
6. When fitting the wheel, follow the correct sequence for the screws as well as the recommended tightening torque.
 
General and safety information
 
This Brembo product has been designed to comply with all applicable safety standards. Products are not intended to be used differently from the specific use for which they have been designed and manufactured. Use for any other purpose, or any modification to or tampering with the Product can affect the performance of the Product and may render the Product unsafe.
 
Such modification or improper use will void the Limited Warranty, and may subject the individual so using the Product to liability for bodily injury or property damage to others.

In these instructions, the “DANGER!” warning means procedures which, if not observed, have a high degree of probability that they will cause serious injury or even death.CAUTION” means procedures which, if not observed, could result in physical damage whereas “WARNING!” means procedures which, if not observed, could possibly cause  damage to the vehicle.
 

DANGER!
Before commencing replacement, ascertain that the spare parts are suitable for the make and model of the vehicle. This Product is vital to the safe operation of the vehicle on which it is installed, and it is intended to be installed only by a skilled, qualified individual who has been trained and/or is experienced in the installation and use for which the Product is intended.

The installer must be equipped with the proper tools of his trade, and with the knowledge and experience to deal with vehicle repairs. Improper or incorrect installation, whether caused by a failure to follow these Instructions faithfully and completely or otherwise, will void the Limited Warranty and could subject the installer to liability in the event of personal injury or property damage.
 

It is essential that you replace the brake discs for each axle, taking them from the same box. Every time you replace the discs also replace the related pads.

Avoid contact of grease and other lubricants with the braking surfaces of the disc and pads as this could affect the efficiency of the braking system.
 
Brembo shall not be liable for any damage or injury caused to or by any person operating a vehicle on which a replacement product has been improperly installed.

 

CAUTION!

Replaced parts must be disposed of in accordance with the law.
It is vital to avoid sharply striking and/or damaging the Product, its parts and its components, as this can impair their efficiency and may cause them to malfunction. If necessary, replace any damaged part or component.
To avoid injury we recommend the following:
  • Always wear gloves during disassembly and assembly of components with sharp edges.
  • Do not allow skin surface to make direct contact with the friction material of pads and brake shoes since this could cause abrasions.
Warranty limitations
This warranty covers all the conformity defects occurring within two years from delivery of the good. The consumer is required to report to the seller the conformity defect within two months from the date of discovery of the said defect, without prejudice to the fact that the limitations period for taking action aimed at seeking redress for the defect is twenty-six months from delivery of the good. In the event of a conformity defect, the user has the right to repair or replacement of the good, or to an appropriate price reduction or termination of the contract, as established by art. 130 of the Consumer Code, where applicable.

This warranty constitutes the only warranty provided in relation to this product and replaces any other warranties, both verbal and written.

Is there anything else you want to ask?

Contact the Brembo technical support team. Our technicians will get back to you as soon as possible!
Return to the index
Car fitting
Read the next article
Instructions for replacing the brake pads on cars and light commercial vehicles
Privacy Policy">